90° included, 45° per side
A symmetrical 90° included angle corresponds to 45° per side from the tool axis. For a conventional edge chamfer with the tool axis perpendicular to the top face, this produces a 45° chamfer face.

Chamfer mills cut an angled edge to the size shown on your part drawing. MSU’s 4SCHA four-flute carbide range uses a 90° included angle.
Check the drawing’s angle convention, chamfer size and access. Then match cutter diameter, tip clearance and cutting length.
Send the 4SCHA model and quantity, or a drawing with the chamfer callout.
Find a Chamfer MillIdentify whether the drawing gives the cutter’s included angle or an angle measured from a part surface.
Tool family
4SCHA90°
Included angle
4-Flute 90° Chamfer Mill
A symmetrical 90° included angle corresponds to 45° per side from the tool axis. For a conventional edge chamfer with the tool axis perpendicular to the top face, this produces a 45° chamfer face.
A different drawing reference or tool orientation changes how the angles relate. Include the reference face and tool approach when specifying the requirement.
Check the cutting diameter and length for the required chamfer size.
Compare 4SCHA SizesAll sizes below use the 90° included-angle 4SCHA profile. Dimensions are in millimeters.
| Model | Diameter d1 | Cutting length L1 | Shank D | Overall length L |
|---|---|---|---|---|
| 4SCHA03350 | 3 | 1 | 3 | 50 |
| 4SCHA04450 | 4 | 3 | 4 | 50 |
| 4SCHA05550 | 5 | 3 | 5 | 50 |
| 4SCHA06650 | 6 | 4 | 6 | 50 |
| 4SCHA08860 | 8 | 6 | 8 | 60 |
| 4SCHA01075 | 10 | 8 | 10 | 75 |
| 4SCHA01275 | 12 | 10 | 12 | 75 |
| 4SCHA01480 | 14 | 12 | 14 | 80 |
| 4SCHA16100 | 16 | 14 | 16 | 100 |
| 4SCHA18100 | 18 | 16 | 18 | 100 |
| 4SCHA20100 | 20 | 18 | 20 | 100 |
Tip clearance still needs checking against the part. The table does not specify tip diameter; include any small opening or minimum-tip requirement with the drawing.
Need the full 4SCHA profile? Open the dimensional drawing before ordering.
View the 4SCHA DrawingThe cutter needs enough usable angled edge for the chamfer, with clearance at the tip and around the holder.
Selection help
The End Mill Selection Guide covers general setup considerations. For an angle or tip requirement that differs from the 90° 4SCHA options, discuss the drawing through Custom Cutting Tools.
Email the chamfer detail when angle notation or tip access is unclear.
Discuss a Chamfer DrawingSpecify the tool angle and tip condition alongside the chamfer requirement.
The MSU Factory has Walter HELITRONIC MICRO equipment; Quality Control facilities include a ZOLLER G3 measurement system.
A chamfer dimension on the part and a tolerance on the tool are different requirements. Mark the angle reference, tip condition and usable cutting length on a custom tool drawing.
Need a measurement report? State the tool dimensions to be reported with your enquiry.
Discuss Inspection RequirementsFor a repeat order, send the full model and quantity. For selection help, email the part detail and material to Maria.
Normally 5–10 pieces; the quotation confirms the quantity for your selected tools.
Samples are charged. Sample freight is paid by the customer.
Your quotation confirms production timing. Shipping time is stated separately.
Maria: maria@msutools.com · +86 13973369578 (phone or WhatsApp). Email drawings and photos.
Downloads has the full product drawings. See Ordering and Delivery for purchasing terms.
Send the chamfer angle and size so we can check the tool against your drawing.
Use the part drawing’s size, angle, reference face and tolerance. A tool’s included angle describes its geometry; the tool orientation determines how that geometry meets the part.
No. A cutter can have enough outside diameter for the chamfer but still interfere at a small opening. The listed dimensions do not specify tip diameter, so a minimum-tip requirement needs separate confirmation.
No. The listed 4SCHA models have a 90° included angle. A different angle or tip profile needs a separate assessment against the part drawing.
Neither capability is established by the chamfer specification shown here. A drilling or countersinking operation needs a tool selected for that operation.