Send Your Inquiry

Tell us about your application and the tools you need.

* Required fields

Skip to content
Ceramic inserts displayed alongside turning toolholders

Ceramic Inserts

Choose ceramic turning and milling inserts by workpiece material, interruption pattern and edge preparation. The range includes composite, alumina-based, whisker and SiAlON ceramic grades.

Match the full insert size and clamping geometry to your holder or cutter. Then select the grade and cutting edge for the allowance, entry conditions and surface requirement.

Send the full insert and holder references, or email the part drawing and material.

Find a Ceramic Insert

Compare the Ceramic Material Families

The grade determines the cutting material; the insert form determines fit and access. Keep both with the edge-preparation designation when comparing a replacement.

Ceramic inserts in round square and polygonal forms
Cutting material Choose the grade for the workpiece and cut.
08

Ceramic grade codes

Composite, alumina-based, whisker and SiAlON grades.

Composite ceramic CX10
Alumina-based ceramic CA10 · CA20
Whisker ceramic CW10 · CW25
SiAlON ceramic CS30 · CS35 · CS40

Compare the material family, grade and expected contact with the workpiece.

Compare Grade and Edge

Select the Grade and Prepared Edge

A sharp edge, hone and chamfer have different contact geometry. Define the land width, land angle and hone where required, together with the grade and cutting conditions.

Ceramic inserts displayed with indexable cutter bodies
Ceramic insert grade, prepared edge and application comparison.
Selection factor What to specify Effect on the cut
Insert form Full size, thickness and clamping geometry Establishes seating and access to the feature.
Ceramic grade CX10, CA10/CA20, CW10/CW25 or CS30/CS35/CS40 Selects the material for workpiece condition and interruptions.
Edge preparation Sharp, honed, chamfered or a combined preparation Changes edge support and contact with the workpiece.
Land and hone Chamfer width, angle and hone size Defines the prepared edge beyond the base insert shape.
Allowance and entry Cut depth, surface scale and interruption pattern Determines how the edge enters and remains in the cut.
Cutting conditions Speed, feed, holder stability and coolant method Provides the operating context for the grade and edge.

Check the prepared edge with the allowance and interruption pattern.

Check the Ceramic Insert Setup

Describe the Cut and Current Edge Damage

For a repeat order, retain the approved grade and edge. For a change, identify where wear or chipping occurs and how the cutting edge enters the workpiece.

  • WorkpieceState material grade, hardness, heat treatment and scale.
  • Cut and allowanceDescribe turning or milling, stock allowance and entry conditions.
  • InterruptionsShow keyways, gaps or interrupted surfaces on the part section.
  • Insert and edgeRetain full code, grade, land width, angle and hone where specified.
  • Holder or cutterIdentify the pocket, clamp, supported edge and tool projection.
  • Current resultRecord cutting data, coolant and where wear, chipping or finish changes occur.
MSU operator at a ZOLLER tool measurement station

Repeat replacement

Keep the complete size, grade and prepared edge from the approved tool. Add the holder reference if the existing tool is unfamiliar.

Wear or chipping

Photograph the used edge and note whether damage occurs at entry, at an interruption or after time in cut.

Trial acceptance

State the dimensional and surface limits to meet. Keep the same measurements when comparing grades or edge preparations.

Email photos of the used edge with the material and current cutting data.

Discuss a Ceramic Insert

Compare Grade Applications and Insert Sizes

Match the grade to the workpiece and continuity of the cut. Then check that the required insert size and edge preparation are available in that grade.

Labeled ceramic insert assortment
22 Insert families
Grade applications

Match material and interruption conditions

CX10 · composite An option for semi-finishing and finishing, including heat-resistant-alloy applications. Match the selected insert and edge to the actual workpiece.
CA10 and CA20 · alumina based CA10 includes continuous to lightly interrupted hardened-steel cutting and cast-iron finishing. CA20 adds a semi-finishing option for these workpiece groups.
CW10 and CW25 · whisker CW10 emphasizes finishing applications. CW25 includes nickel- and cobalt-based alloys in continuous or lightly interrupted cutting, as well as specified cast-iron and hardened-steel work.
CS30, CS35 and CS40 · SiAlON CS30 addresses roughing and semi-finishing of heat-resistant alloys. CS35 includes scale removal and end milling. CS40 addresses scale removal and interrupted cutting of heat-resistant alloys and cast iron.

Insert families

Retain the size and preparation suffix after the family letters when matching an existing insert.

C
CDH CNGA CNGN CNGX
D
DNGA DNGN
L
LNJ
R
RCGX RNGN RPGN RPGX
S
SNGA SNGN SNGX SPGN
T
TNGA TNGN
V
VNGA VGW VGW...R
Z
ZT
W
WNGA
Size example

CNGA 120408 T01020

  • IC: 12.7 mm
  • Thickness: 4.76 mm
  • Nose radius: 0.8 mm
  • T01020: 0.10 mm land at 20°
  • Select the grade with the full designation
  • Check the holder seat and clamp

This example shows how the insert size and prepared edge are specified separately. Grade options for this size include CA10, CA20, CW25 and CS35. Match the grade to the workpiece and cut.

Open Downloads

Keep the grade and preparation suffix with the complete size reference.

View Ceramic Insert Dimensions

Check Insert Dimensions and the Finished Feature

Use the insert drawing for seating and edge measurements. Use the component drawing for finished dimensions, profile and surface acceptance.

MSU operator at a ZOLLER tool measurement station

Tool dimensions

Specify insert thickness, seating dimensions, nose radius and the land or hone to measure. Keep the full preparation designation with the inspection requirement.

Cutting edge

State the edge preparation, radius or cutting-edge features to be measured.

Part acceptance

Use the component drawing to define the finished dimensions and surface requirements for the trial.

  • Dimensional measurements
  • Edge inspection where specified
  • Tool and grade identification
  • Agreed packaging and labels

Request any required reports before ordering so the measured features and document scope can be agreed.

Keep the tool reference and cutting conditions with the finished-part measurements.

Identify critical insert dimensions and any reports required with the order.

View Inspection Information

Order a Replacement or Discuss a Drawing

For a repeat order, send the complete tool reference and quantity. For a new job, email the drawing and describe the feature or machining problem. Ordering and Delivery covers MOQ, payment and shipping. Tool drawings are available in Downloads.

MSU operator at a ZOLLER tool measurement station

Repeat order or new job

Send the full insert code, grade, edge suffix and quantity, or email the part drawing, holder reference and cutting conditions.

MOQ and samples

MOQ is normally 5–10 pieces, confirmed for the selected product. Samples and sample freight are charged.

Delivery and payment

Availability, production and shipping timing are confirmed in the quotation. T/T deposit and balance terms are stated with the order.

Shipping and packaging

Include the destination and required packaging. Delivery terms are agreed for the order.

After-sales support

If a tool or dimension is in question, retain the order reference, measurements and photos so the issue can be investigated.

Contact

Email Maria at maria@msutools.com or call/WhatsApp +86 13973369578. Send drawings and photos by email.

Confirm the selected insert, grade, quantity and delivery.

View Ordering and Delivery

Ceramic Inserts Questions

Compare the actual workpiece, hardness, scale and continuous or interrupted contact. CA, CW, CS and CX grades have different material and process applications; match the grade with the insert and prepared edge.

A chamfer is a small land with a specified width and angle. A hone rounds the cutting edge. A combined preparation includes both, so retain the complete suffix when ordering.

In the illustrated ISO preparation system, it specifies a chamfer with a 0.20 mm land at 20° plus a 0.04 mm hone. Keep that system and the complete insert designation with the order.

Check full dimensions, seating, clamping and support against the holder specification. Then select the ceramic grade and prepared edge for the workpiece and cutting conditions.

Email the required land width, angle, hone and insert reference with the material and cutting conditions. Include a drawing for any non-standard profile.

Include the insert code, grade, preparation, material, allowance and interruptions. Photograph the failed edge and record the holder setup, cutting data and coolant delivery.